caution observe precautions when handling because these devices are sensitive to electrostatic discharge. hetero junction field effect transistor ne3503m04 c to ku band super low noise and high-gain amplifier n-channel hj-fet features ? super low noise figure and high associated gain nf = 0.45 db typ., g a = 12.0 db typ. @ v ds = 2 v, i d = 10 ma, f = 12 ghz ? flat-lead 4-pin thin-type super minimold (m04) package ? gate width: w g = 160 m applications ? dbs lnb gain-stage, mix-stage ? low noise amplifier for microwave communication system ordering information part number order number package quantity marking supplying form ne3503m04 ne3503m04-a flat-lead 4-pin thin- type super minimold (m04) (pb-free) 50 pcs (non reel) v75 ? 8 mm wide embossed taping ? pin 1 (source), pin 2 (drain) face the perforation side of the tape ne3503m04-t2 ne3503m04-t2-a 3 kpcs/reel ne3503m04-t2b ne3503m04-t2b-a 15 kpcs/reel remark to order evaluation samples, contact your nearby sales office. part number for sample order: ne3503m04-a absolute maximum ratings (t a = +25 c) parameter symbol ratings unit drain to source voltage v ds 4.0 v gate to source voltage v gs ?3.0 v drain current i d i dss ma gate current i g 80 a total power dissipation p tot 125 mw channel temperature t ch +125 c storage temperature t stg ?65 to +125 c document no. pg10456ej03v0ds (3rd edition) date published january 2009 ns the mark shows major revised points. the revised points can be easily searched by copying an "" in the pdf file and spec ifying it in the "find what:" field. 2003, 2009
ne3503m04 recommended operating conditions (t a = +25 c) parameter symbol min. typ. max. unit drain to source voltage v ds 1 2 3 v drain current i d 5 10 15 ma input power p in ? ? 0 dbm electrical characteristics (t a = +25 c, unless otherwise specified) parameter symbol test conditions min. typ. max. unit gate to source leak current i gso v gs = ?3.0 v ? 0.5 10 a saturated drain current i dss v ds = 2 v, v gs = 0 v 25 40 70 ma gate to source cutoff voltage v gs (off) v ds = 2 v, i d = 100 a ?0.2 ?0.7 ?1.5 v transconductance g m v ds = 2 v, i d = 10 ma 40 55 ? ms noise figure nf v ds = 2 v, i d = 10 ma, f = 12 ghz ? 0.45 0.65 db associated gain g a 11.0 12.0 ? db data sheet pg10456ej03v0ds 2
ne3503m04 typical characteristics (t a = +25 c, unless otherwise specified) total power dissipation p tot (mw) ambient temperature t a (c) vs. ambient temperature total power dissipation 250 200 150 125 100 50 0 50 100 125 150 200 250 80 60 40 20 0 ?2.0 ?1.0 0 drain current i d (ma) gate to source voltage v gs (v) drain current vs. gate to source voltage v ds = 2 v 1.6 1.0 1.2 1.4 0.8 0.6 0.2 0.4 0.0 16 10 12 14 8 6 2 4 0 10 15 0 5 20 25 30 drain current i d (ma) minimum noise figure nf min (db) associated gain g a (db) associated gain vs. drain current minimum noise figure, f = 12 ghz v ds = 2 v nf min g a 2.0 1.2 1.4 1.6 1.8 0.6 0.8 1.0 0.2 0.4 0.0 25 15 10 5 20 0 68 24 10 01 2 1 4 1 6 1 8 frequency f (ghz) minimum noise figure nf min (db) associated gain g a (db) associated gain vs. frequency minimum noise figure, v ds = 2 v i d = 10 ma 2 0 nf min g a drain current i d (ma) drain to source voltage v ds (v) drain to source voltage drain current vs. 100 20 40 60 80 0 1.0 2.0 v gs = 0 v ?0.2 v ?0.4 v ?0.6 v remark the graphs indicate nominal characteristics. data sheet pg10456ej03v0ds 3
ne3503m04 s-parameters s-parameters and noise parameters are provided on our web site in a format (s2p) that enables the direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. click here to download s-parameters. [rf and microwave] [device parameters] url http://www.necel.com/microwave/en/ data sheet pg10456ej03v0ds 4
ne3503m04 package dimensions flat-lead 4-pin thin-type super minimold (m04) (unit: mm) pin connections 1. source 2. drain 3. source 4. gate 0.590.05 0.11 +0.1 ?0.05 (bottom view) 43 12 1.25 2.00.1 1.30 (1.05) 0.60 0.65 0.65 0.65 1.30 1.25 2.00.1 12 43 1.250.1 2.050.1 0.30 +0.1 ?0.05 0.40 +0.1 ?0.05 0.30 +0.1 ?0.05 0.30 +0.1 ?0.05 v75 data sheet pg10456ej03v0ds 5
ne3503m04 mounting pad dimensions flat-lead 4-pin thin-type super minimold (m04) (unit: mm) ? reference 1 ? 0.8 0.74 1 3 2 4 1.0 1.0 0.9 1.0 0.3 th ? reference 2 ? 2 1 3 4 0.6 1.6 1.25 1.3 0.6 0.5 data sheet pg10456ej03v0ds 6
ne3503m04 recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other t han those recommended below, contact your nearby sales office. soldering method soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 c or below time at peak temperature : 10 seconds or less time at temperature of 220 c or higher : 60 seconds or less preheating time at 120 to 180 c : 12030 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin fl ux (% mass) : 0.2%(wt.) or below ir260 partial heating peak temperature (pin temperature) : 350 c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin fl ux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering met hods together (except for partial heating). data sheet pg10456ej03v0ds 7
data sheet pg10456ej03v0ds 8 ne3503m04 the information in this document is current as of january, 2009. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec electronics data sheets or data books, etc., for the most up-to-date specifications of nec electronics products. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec electronics. nec electronics assumes no responsibility for any errors that may appear in this document. nec electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec electronics products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec electronics or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. nec electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec electronics endeavors to enhance the quality, reliability and safety of nec electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. nec electronics products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to nec electronics products developed based on a customer- designated "quality assurance program" for a specific application. the recommended applications of an nec electronics product depend on its quality grade, as indicated below. customers must check the quality grade of each nec electronics product before using it in a particular application. the quality grade of nec electronics products is "standard" unless otherwise expressly specified in nec electronics data sheets or data books, etc. if customers wish to use nec electronics products in applications not intended by nec electronics, they must contact an nec electronics sales representative in advance to determine nec electronics' willingness to support a given application. (note) ? ? ? ? ? ? m8e 02. 11-1 (1) (2) "nec electronics" as used in this statement means nec electronics corporation and also includes its majority-owned subsidiaries. "nec electronics products" means any product developed or manufactured by or for nec electronics (as defined above). computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. "standard": "special": "specific":
ne3503m04 caution gaas products this product uses gallium arsenide (gaas). gaas vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. ? follow related laws and ordinances when disposi ng of the product. if there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. commission a disposal company able to (wit h a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. exclude the product from general industria l waste and household garbage, and ensure that the product is controlled (as industrial waste subjec t to special control) up until final disposal. ? do not burn, destroy, cut, crush, or chemically dissolve the product. ? do not lick the product or in any way allow it to enter the mouth.
|
